GetDotted Domains

Viewing Thread:
"Gameboy Advance Backlight installed ..."

The "General Games Chat" forum, which includes Retro Game Reviews, has been archived and is now read-only. You cannot post here or create a new thread or review on this forum.

Fri 21/06/02 at 20:19
Regular
Posts: 787
FIRST IMPRESSIONS:

As many of you know , about a year ago , a guy called Adam Curtis , started to make a back light for the GBA. About a year on , and it's reality ! And how gooder reality it is !

I recieved mine on wednesday morning , because im only 14 , i had to go to school , so i installed it that night.

It comes in a small package , wrapped in a bubble wrap envelope.
The instructions are all published like real published book and each part of the kit is well constructed and easy to install.

INSTALLATION :

So I start out by taking apart my GBA with the tri head screw driver that I got with it (from liksang) , which took all of 2 minutes.

Next I follow the easy instructions , and start to CUT my gameboy ! yep you heard me right , CUT my beloved gameboy.
I mark out the bit I have to cut it out , and do it , which took me about 20 odd minutes to get it right (im a bit of a perfectionist) so that the light would fit into it.
Luckily the bit that you have to cut out is where the black gameboy advance logo is , so when you put the screen back on you cant see the damage , phew !

Now I have to put some reflective film on the lcd screen , which stops the light from reflecting … this is when the problems start :(

I determine which side of the film is sticky , line it up with screen , get the black plastic card that is provided , and lift up the corner of the “release film” , my heart sinks when a tiny bit of the glue layer lifts off , and im left with a corner with smudged up glue on it … DAM ! ..and … it’s visible from the outside ! But I can’t change that now , so I carry on.
The non reflective layer , goes on perfectly without any bubbles or anything underneath it … nice.

Now I have to solder … uh oh ;) In the past I have ruined things by soldering for too long , but I’ve learnt from my mistakes and .. start to solder. I have to put the black and red wires onto the ribbon cable coming from the afterburner (the light), which surprisingly is very easy , and goes off without a hitch ! wahoo !

For the next hour or so , I’m fiddling about inside my gameboy (and out) fitting a resistor to a very small terminal thingy ( like fitting a switch to your gamecube) that also surprisingly goes very very well , and I get it right first time ! Now the real problems start, problems that almost make me give up…

I could finish it now , and just have the light inside without a switch on the outside to change the brightness. I thought it would be pretty easy , and cool to have this brightness switch so I go for it … oh what a terrible mistake it was.

To start with I have to make 4 small holes on the right hand side of the gameboy (on the back , below the r button). To do this I use my soldering iron , and then flatten them out with my screw driver.
All going well to far, then I put the brightness dial on , and I notice a problem , I made the holes to far up , so soldering is hard.

To cut a long story short , I try and try to solder the wires to these 2 (the other 2 prongs were used for mounting only) very close together prongs , and succeed, when I try to put the GBA back to together the wires get caught on the game cartridge bit , where you put in the games , and they snap. This happens twice on the second time , I am so demoralised , that I just forget the dial , and finish it without it. I can go back and fit it later if I want to.

OVERALL:

The overall result , is probably the best add on I have ever bought ! I can see my screen , AT LAST !
I can actually look directly at the screen without having to tilt it towards the light. And most of all, I can see it perfectly at night, and the graphics and the whole game in general looks excellent, and I can honestly say they look better with the light.

I may have made it sound as if it was a nightmare to install, but it really wasn’t. The hardest part was having to cut out bits of plastic from the casing, and fitting that switch (but that could have been easy if I had put it in the right place, I could have made new holes , but I thought it might look messy) .

All in all , for £30 , it’s well worth the money , it will enhance your games playing by infinite amounts (unless of course you break your gameboy in the process of installing it , but it seems very hard to actually break it). The only problem with it is , that the light is SO bright , that after a while of playing in pitch darkness it does hurt your eyes a bit , but that’s what happens with most bright lights. And of course , you wont be able to play during lessons , that you have to watch boring videos, and they turn off the lights , because the gameboy turns into a light itself , it’s just that bright.

RATING : 10/10 !

SUPERB
Sat 22/06/02 at 11:15
Regular
"what is knowledge ?"
Posts: 2,112
i know it voids the warantee , but when was the last time you actually used one of those for a console ? It's very rare that you will ever have to use it , so by enhancing my gba , i am voiding the warrantee , but you've gotta take risks in life , and this risk was well worth it.
Fri 21/06/02 at 23:46
Regular
"Chavez, just hush.."
Posts: 11,080
Edgy wrote:
> Nintendo's own guarantee warranties last 24 months I think (I'm sure
> that's what it says in my GameCube box anyway)

Thats right, dunno about the GBA though, anyway i'm gonna keep my GC in one piece!
Fri 21/06/02 at 23:08
Regular
Posts: 15,681
Nintendo's own guarantee warranties last 24 months I think (I'm sure that's what it says in my GameCube box anyway)
Fri 21/06/02 at 22:17
Regular
"Chavez, just hush.."
Posts: 11,080
By taking your Gameboy apart you are voiding your original guarentee from Nintendo!

Be careful when you take it apart or you could ruin the whole thing!
Fri 21/06/02 at 20:43
Regular
"what is knowledge ?"
Posts: 2,112
no , you dont get a guarantee , but do you really need one ?
i mean , if you do it all carefully there should be no problem , and anyway , your origninal gurantee only lasts about 6 months , so it should have expired by now anyway ;)
Fri 21/06/02 at 20:39
Regular
Posts: 14,437
I think I know the answer to this next question, but, do you get any kind of guarantee? Since you are taking apart and literally cutting your GBA to bits? (not that drastic, but you know what I mean)
Fri 21/06/02 at 20:36
Regular
"what is knowledge ?"
Posts: 2,112
yep , £30 including postage , from liksang , or £35 from portablegamer
Fri 21/06/02 at 20:33
Regular
Posts: 14,437
fosbe wrote:
> SOunds good how much did it cosT?

£30. Says so near the end doesn't it?
Fri 21/06/02 at 20:30
Regular
"ProGolfer"
Posts: 2,085
SOunds good how much did it cosT?
Fri 21/06/02 at 20:19
Regular
"what is knowledge ?"
Posts: 2,112
FIRST IMPRESSIONS:

As many of you know , about a year ago , a guy called Adam Curtis , started to make a back light for the GBA. About a year on , and it's reality ! And how gooder reality it is !

I recieved mine on wednesday morning , because im only 14 , i had to go to school , so i installed it that night.

It comes in a small package , wrapped in a bubble wrap envelope.
The instructions are all published like real published book and each part of the kit is well constructed and easy to install.

INSTALLATION :

So I start out by taking apart my GBA with the tri head screw driver that I got with it (from liksang) , which took all of 2 minutes.

Next I follow the easy instructions , and start to CUT my gameboy ! yep you heard me right , CUT my beloved gameboy.
I mark out the bit I have to cut it out , and do it , which took me about 20 odd minutes to get it right (im a bit of a perfectionist) so that the light would fit into it.
Luckily the bit that you have to cut out is where the black gameboy advance logo is , so when you put the screen back on you cant see the damage , phew !

Now I have to put some reflective film on the lcd screen , which stops the light from reflecting … this is when the problems start :(

I determine which side of the film is sticky , line it up with screen , get the black plastic card that is provided , and lift up the corner of the “release film” , my heart sinks when a tiny bit of the glue layer lifts off , and im left with a corner with smudged up glue on it … DAM ! ..and … it’s visible from the outside ! But I can’t change that now , so I carry on.
The non reflective layer , goes on perfectly without any bubbles or anything underneath it … nice.

Now I have to solder … uh oh ;) In the past I have ruined things by soldering for too long , but I’ve learnt from my mistakes and .. start to solder. I have to put the black and red wires onto the ribbon cable coming from the afterburner (the light), which surprisingly is very easy , and goes off without a hitch ! wahoo !

For the next hour or so , I’m fiddling about inside my gameboy (and out) fitting a resistor to a very small terminal thingy ( like fitting a switch to your gamecube) that also surprisingly goes very very well , and I get it right first time ! Now the real problems start, problems that almost make me give up…

I could finish it now , and just have the light inside without a switch on the outside to change the brightness. I thought it would be pretty easy , and cool to have this brightness switch so I go for it … oh what a terrible mistake it was.

To start with I have to make 4 small holes on the right hand side of the gameboy (on the back , below the r button). To do this I use my soldering iron , and then flatten them out with my screw driver.
All going well to far, then I put the brightness dial on , and I notice a problem , I made the holes to far up , so soldering is hard.

To cut a long story short , I try and try to solder the wires to these 2 (the other 2 prongs were used for mounting only) very close together prongs , and succeed, when I try to put the GBA back to together the wires get caught on the game cartridge bit , where you put in the games , and they snap. This happens twice on the second time , I am so demoralised , that I just forget the dial , and finish it without it. I can go back and fit it later if I want to.

OVERALL:

The overall result , is probably the best add on I have ever bought ! I can see my screen , AT LAST !
I can actually look directly at the screen without having to tilt it towards the light. And most of all, I can see it perfectly at night, and the graphics and the whole game in general looks excellent, and I can honestly say they look better with the light.

I may have made it sound as if it was a nightmare to install, but it really wasn’t. The hardest part was having to cut out bits of plastic from the casing, and fitting that switch (but that could have been easy if I had put it in the right place, I could have made new holes , but I thought it might look messy) .

All in all , for £30 , it’s well worth the money , it will enhance your games playing by infinite amounts (unless of course you break your gameboy in the process of installing it , but it seems very hard to actually break it). The only problem with it is , that the light is SO bright , that after a while of playing in pitch darkness it does hurt your eyes a bit , but that’s what happens with most bright lights. And of course , you wont be able to play during lessons , that you have to watch boring videos, and they turn off the lights , because the gameboy turns into a light itself , it’s just that bright.

RATING : 10/10 !

SUPERB

Freeola & GetDotted are rated 5 Stars

Check out some of our customer reviews below:

Great services and friendly support
I have been a subscriber to your service for more than 9 yrs. I have got at least 12 other people to sign up to Freeola. This is due to the great services offered and the responsive friendly support.
LOVE it....
You have made it so easy to build & host a website!!!
Gemma

View More Reviews

Need some help? Give us a call on 01376 55 60 60

Go to Support Centre
Feedback Close Feedback

It appears you are using an old browser, as such, some parts of the Freeola and Getdotted site will not work as intended. Using the latest version of your browser, or another browser such as Google Chrome, Mozilla Firefox, or Opera will provide a better, safer browsing experience for you.