The "Sony Games" forum, which includes Retro Game Reviews, has been archived and is now read-only. You cannot post here or create a new thread or review on this forum.
This may have been discussed before, and if it has I apologise, but I've only just encountered the following problem.
I have a PS 2 with the DVD Region X, hooked up via a full SCART lead and everything worked fine, DVDs from Region 1 played fine and I was a happy camper.
For Xmas, I was lucky enough to receive the official Sony DVD Remote. So, as instructed, I copied the DVD Driver software onto a memory card, plugged the remote receiver in, and tried to watch a DVD.
Now, I have the DVD Region X card in Memory Card Slot 1, the Memory Card with the DVD Driver in Memory Card Slot 2, the remote receiver in Contoller Port 2, and the standard controller in Port 1.
The Region X CD loads fine and I can select the region i want to play, but when I play a Region 1 disk, it come sup in green (the problem that a full RGB SCART lead fixed), and told me the disk could not be played on this system. It was the same with all my Region 1 DVD's.
I tried removing the Memory card with the updated DVD driver on it, and, surprisingly, everything functioned as I would expect - excpet my DVD remote didn't work correctly, as I was expecting because the required memory card wasn't plugged in.
Anyone else encountered this issue, and could anyone suggest a reasonable solution that doesn't involve buying yet more equipment? if push comes to shove I'll just not bother using the new DVD Driver!
I have a PS 2 with the DVD Region X, hooked up via a full SCART lead and everything worked fine, DVDs from Region 1 played fine and I was a happy camper.
For Xmas, I was lucky enough to receive the official Sony DVD Remote. So, as instructed, I copied the DVD Driver software onto a memory card, plugged the remote receiver in, and tried to watch a DVD.
Now, I have the DVD Region X card in Memory Card Slot 1, the Memory Card with the DVD Driver in Memory Card Slot 2, the remote receiver in Contoller Port 2, and the standard controller in Port 1.
The Region X CD loads fine and I can select the region i want to play, but when I play a Region 1 disk, it come sup in green (the problem that a full RGB SCART lead fixed), and told me the disk could not be played on this system. It was the same with all my Region 1 DVD's.
I tried removing the Memory card with the updated DVD driver on it, and, surprisingly, everything functioned as I would expect - excpet my DVD remote didn't work correctly, as I was expecting because the required memory card wasn't plugged in.
Anyone else encountered this issue, and could anyone suggest a reasonable solution that doesn't involve buying yet more equipment? if push comes to shove I'll just not bother using the new DVD Driver!
Page:
This may have been discussed before, and if it has I apologise, but I've only just encountered the following problem.
I have a PS 2 with the DVD Region X, hooked up via a full SCART lead and everything worked fine, DVDs from Region 1 played fine and I was a happy camper.
For Xmas, I was lucky enough to receive the official Sony DVD Remote. So, as instructed, I copied the DVD Driver software onto a memory card, plugged the remote receiver in, and tried to watch a DVD.
Now, I have the DVD Region X card in Memory Card Slot 1, the Memory Card with the DVD Driver in Memory Card Slot 2, the remote receiver in Contoller Port 2, and the standard controller in Port 1.
The Region X CD loads fine and I can select the region i want to play, but when I play a Region 1 disk, it come sup in green (the problem that a full RGB SCART lead fixed), and told me the disk could not be played on this system. It was the same with all my Region 1 DVD's.
I tried removing the Memory card with the updated DVD driver on it, and, surprisingly, everything functioned as I would expect - excpet my DVD remote didn't work correctly, as I was expecting because the required memory card wasn't plugged in.
Anyone else encountered this issue, and could anyone suggest a reasonable solution that doesn't involve buying yet more equipment? if push comes to shove I'll just not bother using the new DVD Driver!
I have a PS 2 with the DVD Region X, hooked up via a full SCART lead and everything worked fine, DVDs from Region 1 played fine and I was a happy camper.
For Xmas, I was lucky enough to receive the official Sony DVD Remote. So, as instructed, I copied the DVD Driver software onto a memory card, plugged the remote receiver in, and tried to watch a DVD.
Now, I have the DVD Region X card in Memory Card Slot 1, the Memory Card with the DVD Driver in Memory Card Slot 2, the remote receiver in Contoller Port 2, and the standard controller in Port 1.
The Region X CD loads fine and I can select the region i want to play, but when I play a Region 1 disk, it come sup in green (the problem that a full RGB SCART lead fixed), and told me the disk could not be played on this system. It was the same with all my Region 1 DVD's.
I tried removing the Memory card with the updated DVD driver on it, and, surprisingly, everything functioned as I would expect - excpet my DVD remote didn't work correctly, as I was expecting because the required memory card wasn't plugged in.
Anyone else encountered this issue, and could anyone suggest a reasonable solution that doesn't involve buying yet more equipment? if push comes to shove I'll just not bother using the new DVD Driver!
Unless you have a newer machine (on which Sony have 'blocked' current Region X versions from working), you can get it to work by entering some codes.
Go to http://www.dvdregionx.com and there's a list of codes - it gives you full instructions on how to enter them. Enter these codes and your RegionX should work fine - mine does. Oh, and you can have the RegionX save and the driver update on the same memory card.
Go to http://www.dvdregionx.com and there's a list of codes - it gives you full instructions on how to enter them. Enter these codes and your RegionX should work fine - mine does. Oh, and you can have the RegionX save and the driver update on the same memory card.
you need to update the key codes which are listed at
http://www.dvdregionx.com/english/x_key_codes.htm
you need the codes entitled euro remote V 2.10
http://www.dvdregionx.com/english/x_key_codes.htm
you need the codes entitled euro remote V 2.10
WòókieeMøn§†€® wrote:
> Unless you have a newer machine (on which Sony have 'blocked' current Region X
> versions from working), you can get it to work by entering some codes.
Go to
> http://www.dvdregionx.com and there's a list of codes - it gives you full
> instructions on how to enter them. Enter these codes and your RegionX should
> work fine - mine does. Oh, and you can have the RegionX save and the driver
> update on the same memory card.
beat me to it by seconds
> Unless you have a newer machine (on which Sony have 'blocked' current Region X
> versions from working), you can get it to work by entering some codes.
Go to
> http://www.dvdregionx.com and there's a list of codes - it gives you full
> instructions on how to enter them. Enter these codes and your RegionX should
> work fine - mine does. Oh, and you can have the RegionX save and the driver
> update on the same memory card.
beat me to it by seconds
It DOES work fine if I don't use the memory card with the updated driver on it - I entered the codes from the web site when i first got the DVD Region X, but what's this about a Save for the Region X? Someone enlighten me as to what this is because I don't see that mentioned in any manuals anywhere? I don't know what this "Save" you refer to is!
SteveyboyUK wrote:
> It DOES work fine if I don't use the memory card with the updated driver on it -
> I entered the codes from the web site when i first got the DVD Region X
Okay, it sounds to me like you entered codes for RegionX for your previous on-board driver.
My RegionX worked fine with my on-board driver - version 1.20E, on a launch machine. It sounds like you had to enter codes to get it to work with your on-board DVD driver - let's say, just for example, that your PS2 is a later model with driver 1.40E on-board.
Now you are using the updated driver on the memory card, which is very likely version 2.10E, you will need to enter NEW codes to get RegionX to work with with the new driver.
> but what's this about a Save for the Region X? Someone
> enlighten me as to what this is because I don't see that
> mentioned in any manuals anywhere? I don't know what
> this "Save" you refer to is!
DVD RegionX saves a small file (12k I think it is) on your memory card. This file contains some data for its operation, and includes the codes that you enter so that you don't need to enter them every time you use the product.
I suggest that you use your PS2's browser, DELETE this file, and re-enter the new 2.10E codes - that should get it working. Let us know how you get on.
> It DOES work fine if I don't use the memory card with the updated driver on it -
> I entered the codes from the web site when i first got the DVD Region X
Okay, it sounds to me like you entered codes for RegionX for your previous on-board driver.
My RegionX worked fine with my on-board driver - version 1.20E, on a launch machine. It sounds like you had to enter codes to get it to work with your on-board DVD driver - let's say, just for example, that your PS2 is a later model with driver 1.40E on-board.
Now you are using the updated driver on the memory card, which is very likely version 2.10E, you will need to enter NEW codes to get RegionX to work with with the new driver.
> but what's this about a Save for the Region X? Someone
> enlighten me as to what this is because I don't see that
> mentioned in any manuals anywhere? I don't know what
> this "Save" you refer to is!
DVD RegionX saves a small file (12k I think it is) on your memory card. This file contains some data for its operation, and includes the codes that you enter so that you don't need to enter them every time you use the product.
I suggest that you use your PS2's browser, DELETE this file, and re-enter the new 2.10E codes - that should get it working. Let us know how you get on.
WòókieeMøn§†€® wrote:
> I suggest that you use your PS2's browser, DELETE this file, and
> re-enter the new 2.10E codes - that should get it working. Let us know how you
> get on.
In addition, i think it is best to ensure that the memory card containing the new DVD driver is in slot 1 when you enter the codes. This will ensure that the DVD RegionX file is on the same card as the driver, and therefore that both are accessible when you want to watch a DVD.
> I suggest that you use your PS2's browser, DELETE this file, and
> re-enter the new 2.10E codes - that should get it working. Let us know how you
> get on.
In addition, i think it is best to ensure that the memory card containing the new DVD driver is in slot 1 when you enter the codes. This will ensure that the DVD RegionX file is on the same card as the driver, and therefore that both are accessible when you want to watch a DVD.
does anyone know if i get the remote with updated codes if it will stop the region x on AR2 V2 from working?
The Action Replay products are made by the same people, so - while I cant say for certain - I'd guess that you can upgrade the AR2 unit as well.
You could always ask them via http://www.codejunkies.com/shop/email_us.asp
You could always ask them via http://www.codejunkies.com/shop/email_us.asp
Page: